0519-88112020
 
 
发布信息当前位置: 首页 » 商家供应 » 泵阀设备 » 离心泵 »

泵中之泵,武进热油泵,WRY热油泵,品质超流值得信赖

点击图片查看原图
单价: 面议
起订:
供货总量:
发货期限: 自买家付款之日起 天内发货
有效期至: 长期有效
最后更新: 2015-07-17 15:48
浏览次数: 671
询价
公司基本资料信息
 
 
产品详细说明
 WRY节能泵0519-85389655,常州市凯林热油泵厂多年专业研发制造了第三代高效节能型节能泵,与普通热油泵相比,其节电率可达到35%左右,节能50%左右,客户均反应良好,下面我们分析一下节能泵的相关修护知识:
随着使用时间的增长,节能泵会出现泵油不足,甚至不泵油等故障,主要原因是有关部位磨损过大。节能泵的磨损部位主要有主动轴与衬套、被动叶轮中心孔与轴销、泵壳内腔与叶轮、叶轮端面与泵盖等。润滑油泵磨损后其主要技术指标达不到要求时,应将其拆卸分解,查清磨损部位及程度,采取相应办法予以修复。
镶套后,将内腔搪到要求的尺寸,并把伸出端面的衬套磨去,使其与泵壳结合面平齐。焊缝须紧密而元气孔,与泵盖结合面平面度误差不大于0.05毫米。
主动轴衬套孔的修理:泵盖上的主动轴衬套孔磨损的修理与壳体主动轴衬套孔磨损的修理方法相同。若主动轴与衬套磨损严峻且配合间隙严峻超标时,不仅要更换衬套,而且主动轴也应用镀铬或振动堆焊法将其直径加大,然后再磨削到尺度尺寸,恢复与衬套的配合要求。球形阀座磨损后,可将一钢球放在阀座上,然后用金属棒轻小扣击钢球,直到球阀与阀座密合为止
WRY energy efficient pumps 0519-85389655 Changzhou Kaelin heat pump plant many years of professional development, and manufacturing of the third generation of highly efficient energy-saving pump, compared with ordinary heat pumps, the saving rate can reach 35 percent, saving about 50 percent, customers have responded well, let's analyze the energy-related knowledge to repair the pump:
With the growth in the use of time, there will be less energy efficient pumps pump oil, even oil pump failure, mainly because relevant parts of excessive wear. Energy efficient pumps wear parts are mainly driving shaft and bushing, passive impeller center hole and the axle pin, pump casing and impeller chamber, with the pump impeller end cover. After lubricating oil pump wear its main technical indicators meet the requirements, it should disassemble, to identify the location and degree of wear and take appropriate way to repair.
After the casement, the cavity lining to the required size, and the end face of the bushing extending rubbed off, allowed to bind to the surface flush with the pump housing. Weld must close and Yuan pores, combined with the pump cover face flatness error of less than 0.05 mm.
Repair drive shaft bushing hole: the same drive shaft bushing and repair of the housing bore hole pump drive shaft bushing wear worn cover repair methods. If the driving shaft and bushing wear and with the gap grim grim exceeded, not only to replac the bushings, and a drive shaft also apply chrome or vibration welding method will increase its diameter, and then grinding to measure the size, recovery and bushes The coordination requirements. Spherical valve seat wear and tear, can be placed on the seat of a ball, then with a metal rod light percussion small ball until the ball valve and seat snug
0条 [查看全部]  相关评论
同类供应信息
 
网站首页 | 关于我们 | 联系方式 | 使用协议 | 版权隐私 | 网站地图 | 网站留言 | 广告服务 | 积分换礼 | RSS订阅 | 企业邮箱登陆
Powered by 声谷信息
购物车(0)    站内信(0)     新对话(0)